Bladders for wishbones, tubes and ducts
Silicone bladders that pressurise carbon suspension members, push rods, ducts and intake trumpets from inside, then extract cleanly after the cure.
Industries · Motorsport and high-performance automotive
Silicone bladders, intensifiers and reusable vacuum bags for carbon fibre parts, silicone tools for wind tunnel and prototype parts, and moulded rubber seals, grommets and boots. For race teams from Formula 1 and endurance racing to GT and rally, and the suppliers who build for them.
What race teams need

In motorsport the deadline is the next event, and the part has to be right when it arrives. A bladder that splits on extraction or an intensifier that rounds off a trailing edge costs a weekend, not just a remake.
We design silicone tooling around your laminate, your resin system and your cure cycle: wall thickness that applies even pressure, grades rated for your autoclave, and extraction designed in so the bladder comes out of a finished wishbone or duct without damaging it.
Material documentation, inspection requirements, manufacturing responsibilities and any necessary approvals should be specified and confirmed for your project before work is authorised.
Typical motorsport work
Six families of rubber tooling cover most motorsport enquiries.
Silicone bladders that pressurise carbon suspension members, push rods, ducts and intake trumpets from inside, then extract cleanly after the cure.
Moulded silicone intensifiers and cauls that hold sharp trailing edges, returns and corners on wing elements, endplates, floors and bodywork.
Moulded vacuum bags for panels you make again and again, cutting consumables and bagging time on every cure.
Silicone tools for vacuum casting quick-change aero parts, model parts and fit-check parts in engineering polyurethanes.
Cast and compression-moulded rubber parts: harness grommets, gear lever and steering boots, button covers, grips and cockpit seals.
Composite tooling and rubber parts for supercar, hypercar and specialist vehicle builders running hundreds rather than hundreds of thousands.
Parts and tooling
A general guide. Geometry, laminate and cure cycle decide the final tool.
Typical guide values, confirmed on your quotation. We confirm grade, expected cure life and lead time against your part and cycle.
| Part | Typical tooling | Typical cure | Why rubber tooling helps |
|---|---|---|---|
| Suspension members and push rods | Silicone bladders | Autoclave | Even internal pressure on hollow tubes |
| Wing elements and flaps | Intensifiers and cauls | Autoclave | Sharp trailing edges and corners |
| Ducts and trumpets | Bladders and soft mandrels | Autoclave or oven | Complex hollow shapes that still release |
| Bodywork and floor panels | Reusable vacuum bags, cauls | Autoclave or oven | Fewer consumables, consistent finish |
| Wind tunnel parts | Silicone tools, vacuum casting | Room temperature or oven | Fast, cheap iterations in polyurethane |
| Seals, grommets and boots | Cast or compression-moulded rubber | Press or oven | Short runs without steel tooling |
Send the peak temperature, pressure, dwell and resin system with your enquiry so we can confirm the grade with its data sheet before quoting.
Examples
Eight typical jobs for silicone, polyurethane and rubber tooling in this industry. Each one can be a single development tool or a full production set.
Silicone bladders for hollow carbon wishbones, roll structures and steering columns.
SiliconeShaped pads that consolidate carbon airboxes, ducts and bodywork corners.
SiliconeScale front wings, floors and bodywork details cast quickly for aero testing.
Silicone tool, PU, resinLow-volume rubber seals, grommets and boots for race cars and limited-run road cars.
Silicone, EPDMSilicone bags for repeat carbon parts, cutting bagging time between sessions.
SiliconeVacuum-cast trim, switch panels and interior details for prototypes and low-volume builds.
PU partsMoulded heat shields, pads and mounts for electronics and wiring.
High-temperature siliconeReplacement rubber and trim for classic and heritage vehicles, moulded from originals.
Silicone, PUTooling ideas, clearly explained
Larger customers ask the same questions: how is it checked, what is it made from, and can you make another one exactly the same? This is how we answer them.




Photos: Brandable Box, Jessica Streser, Wilhelm Gunkel, laura adai on Unsplash.
How we work with race teams
Please contact us before sending sensitive drawings or samples so that any confidentiality arrangements can be agreed.
You have a named contact for your programme, from feasibility to repeat supply, and is the person your engineering, quality and procurement teams speak to.
Material documentation, inspection requirements, manufacturing responsibilities and any necessary approvals should be specified and confirmed for your project before work is authorised.
Any tooling-specific terms, expected service conditions and remedies must be confirmed in your written quotation and order agreement.

Programme stages
We review the part, laminate, resin system, cure cycle and deadline, and propose the tooling.
Please contact us before sending sensitive drawings or samples so that any confidentiality arrangements can be agreed.
Master made from your CAD, first bladder or intensifier cast and trial-cured with your laminate.
Wall thickness, fit and extraction tuned from the trial before tools are duplicated.
Matched sets, planned replacements and archived masters for the rest of the season and the next.
Questions from motorsport teams
Lead time depends on the agreed scope, review stages, material availability and current workload. Request a schedule with your quotation.
It depends on the grade, the peak temperature, the pressure and how the bladder is extracted. We propose a grade with its data sheet against your cure cycle and give you an expected cure life, so replacements can be planned into the season rather than discovered on the build floor.
Yes, as standard, before any CAD or part moves. Sensitive programmes are kept to a named team, and masters and tools made for you are never used for anyone else.
Our focus is the tooling: bladders, intensifiers, cauls, reusable vacuum bags and the masters behind them. Where you need finished laminates or machined metal tooling, we can manage that through our vetted partner network as part of the same programme, and we will tell you which is which.
Pricing depends on your design, materials, quantities and tooling scope. Ask us for a quotation against your project brief.
Related industries

Reusable silicone vacuum bags, non-slip deck texture tooling, fitting moulds and rubber seals for yacht, RIB, workboat and marine component builders.
Read more
Supported polyurethane and silicone moulds for precast, GRC, cast stone, formliners and heritage reproduction, with rigid jackets that hold shape.
Read more
High-end custom food-contact moulds for restaurant groups, luxury hotels and pastry kitchens, made through our sister division TCI Culinary: signature desserts, branded chocolate and banqueting tools.
Read moreStart a programme
We will propose the tooling, the expected cure life and a fixed programme price.
Your project, our expertise
Contact TCI Mouldings with your drawings, samples and production requirements so the technical brief and next steps can be discussed.



Thomas LaneManaging Director
George PrestonDesign & Project Manager
Kelly BallingerHead of Partnerships
Jim AndertonProduction Manager
TheodoreEmployee Welfare